OpenOCD starts with a board configuration file. Therein, a configuration file for the processor, the debug interface and a file with initialization sripts can be found.

Our scan chain contains the PL (programmable logic) and the PS (processing system).

Open On-Chip Debugger 0.10.0
Licensed under GNU GPL v2
For bug reports, read
        http://openocd.org/doc/doxygen/bugs.html
srst_only separate srst_gates_jtag srst_push_pull connect_deassert_srst
adapter_nsrst_delay: 40
Info : auto-selecting first available session transport "jtag". To override use 'transport select <transport>'.
adapter speed: 1000 kHz
adapter speed: 10000 kHz
Info : ftdi: if you experience problems at higher adapter clocks, try the command "ftdi_tdo_sample_edge falling"
Info : clock speed 10000 kHz
Info : JTAG tap: zynq_pl.bs tap/device found: 0x13722093 (mfg: 0x049 (Xilinx), part: 0x3722, ver: 0x1)
Info : JTAG tap: zynq.dap tap/device found: 0x4ba00477 (mfg: 0x23b (ARM Ltd.), part: 0xba00, ver: 0x4)
Info : zynq.cpu0: hardware has 6 breakpoints, 4 watchpoints
Info : zynq.cpu1: hardware has 6 breakpoints, 4 watchpoints
   TapName             Enabled  IdCode     Expected   IrLen IrCap IrMask
-- ------------------- -------- ---------- ---------- ----- ----- ------
 0 zynq_pl.bs             Y     0x13722093 0x23727093     6 0x01  0x03
                                           0x13722093
                                           0x03727093
 1 zynq.dap               Y     0x4ba00477 0x4ba00477     4 0x01  0x0f

Usually, deep will open a telnet connection to the OpenOCD server running on the host (through the OpenOCDinterface). For testing purposes it is convenient to open a second telnet connection, e.g. with a terminal program such as Putty.

The PS includes two targets, zynq.cpu0 and zynq.cpu1. These can be listed with the command targets.

    TargetName         Type       Endian TapName            State
--  ------------------ ---------- ------ ------------------ ------------
 0* zynq.cpu0          cortex_a   little zynq.dap           running
 1  zynq.cpu1          cortex_a   little zynq.dap           running

The star denotes the current target, e.g. the reg command will list all registers. To list the registers of cpu1 you have to change the current target with targets zynq.cpu1.

When halting the running targets with halt, the state of the two targets are listed in the console, e.g.

target halted in ARM state due to debug-request, current mode: Supervisor
cpsr: 0x60000113 pc: 0x00101834
MMU: disabled, D-Cache: disabled, I-Cache: disabled
target halted in ARM state due to debug-request, current mode: Supervisor
cpsr: 0x60000193 pc: 0xffffff34
MMU: disabled, D-Cache: disabled, I-Cache: disabled

The output shows the state of the two targets.

Bad USB cable connections can lead to errors such as

Info : accepting 'telnet' connection on tcp/4444
Info : JTAG tap: zynq_pl.bs tap/device found: 0x13722093 (mfg: 0x049 (Xilinx), part: 0x3722, ver: 0x1)
Info : JTAG tap: zynq.dap tap/device found: 0x4ba00477 (mfg: 0x23b (ARM Ltd.), part: 0xba00, ver: 0x4)
Warn : zynq.cpu0: ran after reset and before halt ...
Warn : zynq.cpu1: ran after reset and before halt ...
Error: DSCR_DTR_RX_FULL, dscr 0x4b086003

In such a case, try another cable.