deep

a Cross Development Platform for Java

User Tools

Site Tools

You are here: start » firstexample » first_example_microzed_deploy
firstexample:first_example_microzed_deploy

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
firstexample:first_example_microzed_deploy [2021/05/18 10:49] – [Step by Step Instructions] ursgraffirstexample:first_example_microzed_deploy [2021/07/23 18:47] – [Step by Step Instructions] ursgraf
Line 12: Line 12:
   - Choose a configuration for the FPGA part to be included into the resulting image. \\ {{ chooseplfile.png?300 |}}. \\ Available configurations can be found under [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/microzed]].   - Choose a configuration for the FPGA part to be included into the resulting image. \\ {{ chooseplfile.png?300 |}}. \\ Available configurations can be found under [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/microzed]].
   - When creating the run configuration, set the target configuration to //boot from QSPI flash// {{ runconfigurationmicrozedflash.png?400 |}}.   - When creating the run configuration, set the target configuration to //boot from QSPI flash// {{ runconfigurationmicrozedflash.png?400 |}}.
-  - Running the configuration will create a flash file. Its location is given by the image file setting in the configuration. It carries the name //*.ExternalFlash.mcs//.  +  - Running the configuration will create a flash file. Its location is given by the image file setting in the configuration. It carries the name //*.ExternalFlash.mcs//. Running the configuration will try to open a connection to the target if a programmer is chosen, such as //OpenOCD//. Make sure to remove the programmer, if you have no programmer present.  
   - Switch the driver for your JTAG-HS3 adapter to //FTDI CDM//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]]. IMPORTANT: You must close OpenOCD before switching the driver, else the //WinUSB// cannot be unloaded.   - Switch the driver for your JTAG-HS3 adapter to //FTDI CDM//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]]. IMPORTANT: You must close OpenOCD before switching the driver, else the //WinUSB// cannot be unloaded.
   - The program to download can be found in the binaries of //Vivado// or the //Xilinx SDK//. You have to either install //Vivado// or //Xilinx SDK// which doesn't require a license. As //Vivado// uses lots of disk space we strongly recommend to install //Xilinx SDK//. For the installation see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/xsdk|Installing Xilinx SDK]]. After installation, open a command shell and run the command (Change the command so that the right configuration file is loaded, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/microzed]]). The corresponding files can be found in your target runtime library in the directory ///rsc//. Please make sure that the paths in the following command does not include spaces! <code shell>cmd /C C:\Xilinx\SDK\2019.1\bin\program_flash -f MyProject\App.ExternalFlash.mcs -offset 0 -flash_type qspi-x4-single -fsbl M:\EUser\JCC\org.deepjava.trglib\rsc\FSBL.elf -cable type xilinx_tcf url TCP:127.0.0.1:3121 </code> Make sure that the programming was successful with the program printing <code>Flash Operation Successful</code>   - The program to download can be found in the binaries of //Vivado// or the //Xilinx SDK//. You have to either install //Vivado// or //Xilinx SDK// which doesn't require a license. As //Vivado// uses lots of disk space we strongly recommend to install //Xilinx SDK//. For the installation see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/xsdk|Installing Xilinx SDK]]. After installation, open a command shell and run the command (Change the command so that the right configuration file is loaded, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/microzed]]). The corresponding files can be found in your target runtime library in the directory ///rsc//. Please make sure that the paths in the following command does not include spaces! <code shell>cmd /C C:\Xilinx\SDK\2019.1\bin\program_flash -f MyProject\App.ExternalFlash.mcs -offset 0 -flash_type qspi-x4-single -fsbl M:\EUser\JCC\org.deepjava.trglib\rsc\FSBL.elf -cable type xilinx_tcf url TCP:127.0.0.1:3121 </code> Make sure that the programming was successful with the program printing <code>Flash Operation Successful</code>
firstexample/first_example_microzed_deploy.txt · Last modified: 2022/11/17 15:03 by ursgraf

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki