Differences

This shows you the differences between two versions of the page.

--- firstexample:boot_loader [2022/12/21 08:43] – ursgraf
+++ firstexample:boot_loader [2025/02/18 13:02] (current) – [Flashing a new Boot Loader] ursgraf
@@ Line 13: / Line 13: @@
   - Set the jumpers on your MicroZed board as follows \\ {{ jtagboot.png?200 |}}. \\ This will boot the device from JTAG.
   - Cycle the power. The settings of the jumpers will be read only at power-on! Hence, make sure to cycle the supply power after changing the jumper settings. A soft reset (through the JTAG or by pressing the reset button on the board will reset the board but will not sample the boot mode pins connected to the jumpers.
-  - Switch the driver for your JTAG-HS3 adapter to //FTDI CDM//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]]. IMPORTANT: You must close OpenOCD before switching the driver, else the //WinUSB// cannot be unloaded.
+  - Switch the driver for your JTAG-HS3 adapter to //FTDI CDM//, see [[https://wiki.ost.ch/display/EDS/Digilent+JTAG-HS3]]. IMPORTANT: You must close OpenOCD before switching the driver, else the //WinUSB// cannot be unloaded.
-  - The program to download can be found in the binaries of //Vivado// or //Xilinx Vitis//. You have to either install //Vivado// or //Vitis// which doesn't require a license. As //Vivado// uses lots of disk space we strongly recommend to install //Vitis//. For the installation see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/xsdk|Installing Xilinx SDK]]. After installation, open a command shell and run the command (Change the command so that the right configuration file is loaded, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/microzed]]). The corresponding files can be found in your target runtime library in the directory ///rsc//. Please make sure that the paths in the following command does not include spaces! <code shell>cmd /C C:\Xilinx\Vitis\2020.2\bin\program_flash -f \\ost.ch\dfs\bsc.sys\public-programme\deep\lib\rsc\BOOTflink2.mcs -offset 0 -flash_type qspi-x4-single -fsbl \\ost.ch\dfs\bsc.sys\public-programme\deep\lib\rsc\FSBL.elf -cable type xilinx_tcf url TCP:127.0.0.1:3121</code> Make sure that the programming was successful with the program printing <code>Flash Operation Successful</code>
+  - The program to download can be found in the binaries of //Vivado// or //Xilinx Vitis//. You have to either install //Vivado// or //Vitis// which doesn't require a license. As //Vivado// uses lots of disk space we strongly recommend to install //Vitis//. For the installation see [[https://wiki.ost.ch/pages/viewpage.action?pageId=346161189|Installing Xilinx SDK]]. After installation, open a command shell and run the command (Change the command so that the right configuration file is loaded, see [[https://wiki.ost.ch/display/EDS/MicroZed+Boardhttps://wiki.ost.ch/display/EDS/MicroZed+Board]]). The corresponding files can be found in your target runtime library in the directory ///rsc//. Please make sure that the paths in the following command does not include spaces! <code shell>cmd /C C:\Xilinx\Vitis\2020.2\bin\program_flash -f \\ost.ch\dfs\bsc.sys\public-programme\deep\lib\rsc\BOOTflink2.mcs -offset 0 -flash_type qspi-x4-single -fsbl \\ost.ch\dfs\bsc.sys\public-programme\deep\lib\rsc\FSBL.elf -cable type xilinx_tcf url TCP:127.0.0.1:3121</code> Make sure that the programming was successful with the program printing <code>Flash Operation Successful</code>
-  - Switch the driver for the JTAG-HS3 back to //WinUSB//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]].
+  - Switch the driver for the JTAG-HS3 back to //WinUSB//, see [[https://wiki.ost.ch/display/EDS/Digilent+JTAG-HS3]].

deep

User Tools

Site Tools

Differences

Page Tools