deep

a Cross Development Platform for Java

User Tools

Site Tools

You are here: start » firstexample » boot_loader
firstexample:boot_loader

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
firstexample:boot_loader [2020/12/01 16:26] – [Flashing a new Boot Loader] ursgraffirstexample:boot_loader [2021/12/30 09:39] – ursgraf
Line 2: Line 2:
 Your MicroZed boards need a valid boot loader if you want to start it from the QSPI flash.  Your MicroZed boards need a valid boot loader if you want to start it from the QSPI flash. 
 ===== Check for Valid Boot Loader ===== ===== Check for Valid Boot Loader =====
-  - Set the jumpers on your MicroZed board as follows \\ {{ :qspiboot.png?200 |}}. \\ This will boot the device from the QSPI flash. +  - Set the jumpers on your MicroZed board as follows \\ {{ qspiboot.png?200 |}}. \\ This will boot the device from the QSPI flash. 
   - Cycle the power. The settings of the jumpers will be read only at power-on! Hence, make sure to cycle the supply power after changing the jumper settings. A soft reset (through the JTAG or by pressing the reset button on the board will reset the board but will not sample the boot mode pins connected to the jumpers.   - Cycle the power. The settings of the jumpers will be read only at power-on! Hence, make sure to cycle the supply power after changing the jumper settings. A soft reset (through the JTAG or by pressing the reset button on the board will reset the board but will not sample the boot mode pins connected to the jumpers.
-  - Use a terminal program to open the COM port on J2. +  - Use a terminal program to open the COM port on J2 (Baudrate ''115200''). 
-  - Press reset \\ {{ :firstexample:microzed_reset.png?300 |}} This will reboot the device and cause the boot loader to run again+  - Press reset \\ {{ microzed_reset.png?300 |}} This will reboot the device and cause the boot loader to run again
   - Check if the blue ''done'' led lights up. This signals that the boot loader successfully loaded the FPGA.   - Check if the blue ''done'' led lights up. This signals that the boot loader successfully loaded the FPGA.
-  - Check the output of the terminal program. It show the following output \\ {{ :firstexample:bootloader.png?500 |}}+  - Check the output of the terminal program. It should show the following output \\ {{ bootloader.png?500 |}} 
 +  - If one of the two checks fails you have to flash a new bootloader, see below. 
  
 ===== Flashing a new Boot Loader ===== ===== Flashing a new Boot Loader =====
-  - Set the jumpers on your MicroZed board as follows \\ {{ :jtagboot.png?200 |}}. \\ This will boot the device from JTAG. +  - Set the jumpers on your MicroZed board as follows \\ {{ jtagboot.png?200 |}}. \\ This will boot the device from JTAG. 
   - Cycle the power. The settings of the jumpers will be read only at power-on! Hence, make sure to cycle the supply power after changing the jumper settings. A soft reset (through the JTAG or by pressing the reset button on the board will reset the board but will not sample the boot mode pins connected to the jumpers.   - Cycle the power. The settings of the jumpers will be read only at power-on! Hence, make sure to cycle the supply power after changing the jumper settings. A soft reset (through the JTAG or by pressing the reset button on the board will reset the board but will not sample the boot mode pins connected to the jumpers.
-  - Switch the driver for your JTAG-HS3 adapter to FTDI, see [[https://wiki.ntb.ch/infoportal/embedded_systems/jtaghs3/start]]. +  - Switch the driver for your JTAG-HS3 adapter to //FTDI CDM//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]]. IMPORTANT: You must close OpenOCD before switching the driver, else the //WinUSB// cannot be unloaded. 
-  - Open a command shell and run the command <code shell>cmd /C C:\Xilinx\SDK\2019.1\bin\program_flash -f M:\EUser\JCC\org.deepjava.trglib\rsc\BOOTflink2.mcs -offset 0 -flash_type qspi-x4-single -fsbl D:\Vivado\Booting\Booting.sdk\FSBL\Debug\FSBL.elf -cable type xilinx_tcf url TCP:127.0.0.1:3121 </code> +  - The program to download can be found in the binaries of //Vivado// or //Xilinx Vitis//. You have to either install //Vivado// or //Vitis// which doesn't require a license. As //Vivado// uses lots of disk space we strongly recommend to install //Vitis//. For the installation see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/xsdk|Installing Xilinx SDK]]. After installation, open a command shell and run the command (Change the command so that the right configuration file is loaded, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/microzed]]). The corresponding files can be found in your target runtime library in the directory ///rsc//. Please make sure that the paths in the following command does not include spaces! <code shell>cmd /C C:\Xilinx\Vitis\2020.2\bin\program_flash -f \\ost.ch\dfs\bsc.sys\public-programme\deep\lib\rsc\BOOTflink2.mcs -offset 0 -flash_type qspi-x4-single -fsbl \\ost.ch\dfs\bsc.sys\public-programme\deep\lib\rsc\FSBL.elf -cable type xilinx_tcf url TCP:127.0.0.1:3121</code> Make sure that the programming was successful with the program printing <code>Flash Operation Successful</code> 
-  - Switch the driver for the JTAG-HS3 back to Microsoft, see [[https://wiki.ntb.ch/infoportal/embedded_systems/jtaghs3/start]].+  - Switch the driver for the JTAG-HS3 back to //WinUSB//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]].
firstexample/boot_loader.txt · Last modified: 2022/12/21 08:43 by ursgraf

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki