deep

a Cross Development Platform for Java

User Tools

Site Tools


firstexample:boot_loader

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
firstexample:boot_loader [2021/03/15 17:03] – [Flashing a new Boot Loader] ursgraffirstexample:boot_loader [2021/05/18 10:49] – [Flashing a new Boot Loader] ursgraf
Line 14: Line 14:
   - Cycle the power. The settings of the jumpers will be read only at power-on! Hence, make sure to cycle the supply power after changing the jumper settings. A soft reset (through the JTAG or by pressing the reset button on the board will reset the board but will not sample the boot mode pins connected to the jumpers.   - Cycle the power. The settings of the jumpers will be read only at power-on! Hence, make sure to cycle the supply power after changing the jumper settings. A soft reset (through the JTAG or by pressing the reset button on the board will reset the board but will not sample the boot mode pins connected to the jumpers.
   - Switch the driver for your JTAG-HS3 adapter to //FTDI CDM//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]]. IMPORTANT: You must close OpenOCD before switching the driver, else the //WinUSB// cannot be unloaded.   - Switch the driver for your JTAG-HS3 adapter to //FTDI CDM//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]]. IMPORTANT: You must close OpenOCD before switching the driver, else the //WinUSB// cannot be unloaded.
-  - Open a command shell and run the command (Change the command so that the right configuration file is loaded, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/microzed]]). The corresponding files can be found in your target runtime library in the directory ///rsc//The program to download can be found in the binaries of //Vivado// or the //Xilinx SDK//. You have to either install //Vivado// or //Xilinx SDK// which doesn't require a license. As //Vivado// uses lots of disk space we strongly recommend to install //Xilinx SDK//. For the installation see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/xsdk|Installing Xilinx SDK]] <code shell>cmd /C C:\Xilinx\SDK\2019.1\bin\program_flash -f M:\EUser\JCC\org.deepjava.trglib\rsc\BOOTflink2.mcs -offset 0 -flash_type qspi-x4-single -fsbl M:\EUser\JCC\org.deepjava.trglib\rsc\FSBL.elf -cable type xilinx_tcf url TCP:127.0.0.1:3121</code> Make sure that the programming was successful with the program printing <code>Flash Operation Successful</code>+  - The program to download can be found in the binaries of //Vivado// or the //Xilinx SDK//. You have to either install //Vivado// or //Xilinx SDK// which doesn't require a license. As //Vivado// uses lots of disk space we strongly recommend to install //Xilinx SDK//. For the installation see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/xsdk|Installing Xilinx SDK]]. After installation, open a command shell and run the command (Change the command so that the right configuration file is loaded, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/microzed]]). The corresponding files can be found in your target runtime library in the directory ///rsc//. Please make sure that the paths in the following command does not include spaces! <code shell>cmd /C C:\Xilinx\SDK\2019.1\bin\program_flash -f M:\EUser\JCC\org.deepjava.trglib\rsc\BOOTflink2.mcs -offset 0 -flash_type qspi-x4-single -fsbl M:\EUser\JCC\org.deepjava.trglib\rsc\FSBL.elf -cable type xilinx_tcf url TCP:127.0.0.1:3121</code> Make sure that the programming was successful with the program printing <code>Flash Operation Successful</code>
   - Switch the driver for the JTAG-HS3 back to //WinUSB//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]].   - Switch the driver for the JTAG-HS3 back to //WinUSB//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]].
firstexample/boot_loader.txt · Last modified: 2022/12/21 08:43 by ursgraf