deep

a Cross Development Platform for Java

User Tools

Site Tools

You are here: start » firstexample » boot_loader
firstexample:boot_loader

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
firstexample:boot_loader [2021/12/30 09:32] – ursgraffirstexample:boot_loader [2022/12/21 08:43] (current) – ursgraf
Line 4: Line 4:
   - Set the jumpers on your MicroZed board as follows \\ {{ qspiboot.png?200 |}}. \\ This will boot the device from the QSPI flash.    - Set the jumpers on your MicroZed board as follows \\ {{ qspiboot.png?200 |}}. \\ This will boot the device from the QSPI flash. 
   - Cycle the power. The settings of the jumpers will be read only at power-on! Hence, make sure to cycle the supply power after changing the jumper settings. A soft reset (through the JTAG or by pressing the reset button on the board will reset the board but will not sample the boot mode pins connected to the jumpers.   - Cycle the power. The settings of the jumpers will be read only at power-on! Hence, make sure to cycle the supply power after changing the jumper settings. A soft reset (through the JTAG or by pressing the reset button on the board will reset the board but will not sample the boot mode pins connected to the jumpers.
-  - Use a terminal program to open the COM port on J2 (Baudrate ''115200'').+  - Use a terminal program to open the COM port on the USB_UART (J2, Baudrate ''115200'').
   - Press reset \\ {{ microzed_reset.png?300 |}} This will reboot the device and cause the boot loader to run again   - Press reset \\ {{ microzed_reset.png?300 |}} This will reboot the device and cause the boot loader to run again
   - Check if the blue ''done'' led lights up. This signals that the boot loader successfully loaded the FPGA.   - Check if the blue ''done'' led lights up. This signals that the boot loader successfully loaded the FPGA.
Line 14: Line 14:
   - Cycle the power. The settings of the jumpers will be read only at power-on! Hence, make sure to cycle the supply power after changing the jumper settings. A soft reset (through the JTAG or by pressing the reset button on the board will reset the board but will not sample the boot mode pins connected to the jumpers.   - Cycle the power. The settings of the jumpers will be read only at power-on! Hence, make sure to cycle the supply power after changing the jumper settings. A soft reset (through the JTAG or by pressing the reset button on the board will reset the board but will not sample the boot mode pins connected to the jumpers.
   - Switch the driver for your JTAG-HS3 adapter to //FTDI CDM//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]]. IMPORTANT: You must close OpenOCD before switching the driver, else the //WinUSB// cannot be unloaded.   - Switch the driver for your JTAG-HS3 adapter to //FTDI CDM//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]]. IMPORTANT: You must close OpenOCD before switching the driver, else the //WinUSB// cannot be unloaded.
-  - The program to download can be found in the binaries of //Vivado// or //Xilinx Vitis//. You have to either install //Vivado// or //Vitis// which doesn't require a license. As //Vivado// uses lots of disk space we strongly recommend to install //Vitis//. For the installation see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/xsdk|Installing Xilinx SDK]]. After installation, open a command shell and run the command (Change the command so that the right configuration file is loaded, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/microzed]]). The corresponding files can be found in your target runtime library in the directory ///rsc//. Please make sure that the paths in the following command does not include spaces! <code shell>cmd /C C:\Xilinx\Vitis\2020.2\bin\program_flash -f -fsbl \\ost.ch\dfs\bsc.sys\public-programme\deep\lib\rsc\BOOTflink2.mcs -offset 0 -flash_type qspi-x4-single -fsbl \\ost.ch\dfs\bsc.sys\public-programme\deep\lib\rsc\FSBL.elf -cable type xilinx_tcf url TCP:127.0.0.1:3121</code> Make sure that the programming was successful with the program printing <code>Flash Operation Successful</code>+  - The program to download can be found in the binaries of //Vivado// or //Xilinx Vitis//. You have to either install //Vivado// or //Vitis// which doesn't require a license. As //Vivado// uses lots of disk space we strongly recommend to install //Vitis//. For the installation see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/xsdk|Installing Xilinx SDK]]. After installation, open a command shell and run the command (Change the command so that the right configuration file is loaded, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/zynq7000/microzed]]). The corresponding files can be found in your target runtime library in the directory ///rsc//. Please make sure that the paths in the following command does not include spaces! <code shell>cmd /C C:\Xilinx\Vitis\2020.2\bin\program_flash -f \\ost.ch\dfs\bsc.sys\public-programme\deep\lib\rsc\BOOTflink2.mcs -offset 0 -flash_type qspi-x4-single -fsbl \\ost.ch\dfs\bsc.sys\public-programme\deep\lib\rsc\FSBL.elf -cable type xilinx_tcf url TCP:127.0.0.1:3121</code> Make sure that the programming was successful with the program printing <code>Flash Operation Successful</code>
   - Switch the driver for the JTAG-HS3 back to //WinUSB//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]].   - Switch the driver for the JTAG-HS3 back to //WinUSB//, see [[https://wiki.bu.ost.ch/infoportal/embedded_systems/jtaghs3/start]].
firstexample/boot_loader.1640853137.txt.gz · Last modified: 2021/12/30 09:32 by ursgraf

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki